Terminal-C Connector for Compact IO Modules
£8.36 Exc. VAT
Fdx-Terminal-C set: – 1 pcs female connector. – 1 pcs male connector. – 1 pcs 120 resistor. T-Bus DIN-rail connector.
Terminal-C set: – 1 pcs female connector. – 1 pcs male connector. – 1 pcs 120 Ω resistor. T-Bus DIN-rail connector.
You need only one connector per group of IO modules.
So if you have 1 or 32 IO modules (The typical maximum Modbus device count between repeaters is 32. Supported Modbus RTU serial device count may be limited by manufacturer, cable, and communication speed. Check with the manufacturer for more information), only 1 terminal C is required.
A (DATA +) and B (DATA -) = Modbus RS485 RTU (Remote Terminal Unit) Connection.
Modbus RS-485 is a bidirectional, half-duplex and indicates values using differences in voltage (-7V to +12V).
RS-485 simply stands for Recommended Standard #485, and it’s been around since 1983. It is used for Serial communication.
+ and – = 24VDC Power, from DC power supply.
The blank terminal you can connect to the cable screen (SG – Screen Ground) from the Modbus network if required.
Modbus loop termination: On the last module, the Modbus loop must be closed by connecting a 120 Ω resistor between the A and the B side of the RS-485 loop.
Why 120 ohm is used in RS-485?
In RS485, the twisted pair cable used is defined to have a characteristic impedance of 120 Ohm. By adding a 120-ohm resistor at the end of an RS485 transmission line, the signal will be dampened by the resistor instead of reflected into the bus.
BMS Parts You Tube
[embedyt] https://www.youtube.com/watch?v=xIk-O_HJ7zo[/embedyt]
| Weight | 0.40 kg |
|---|---|
| Dimensions | 1.9 × 1.9 × 1.2 cm |
You must be logged in to post a review.
MAECENAS IACULIS
Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.
ADIPISCING CONVALLIS BULUM
- Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
- Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
- Diam parturient dictumst parturient scelerisque nibh lectus.
Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.
You may also like…
Related products
24 Channel Digital Input Multiplexer – VFC input
The IOD24 module was created and designed to provide a cost-effective and efficient way of handling a large amount of digital input into a Building Management System (BMS). 24 Digital Inputs are multiplexed to provide a single analogue output (0-10V or 4-20mA) which is compatible with most open standard BMS controllers on the market currently.
EB-303 Current Bar
The EC is a current sensor for standard miniature circuit breakers (MCB). It is designed to fit any type of IEC standard MCB, Residual-Current Devices (RCD), and Residual-current Circuit Breakers with Overload protection (RCBO) capable of measuring devices up to 40A. The EC includes a current transformer (CT) with turn ratio of 1:1000 and a burden resistor of 10Ω. The EC does not interfere with or affect the function of the MCB.
LoRa Wireless RS485 transmitter or receiver with LCD screen – 1 Unit
The LoRaWAN Data Transmission Terminal is a universal communication interactive equipment that is designed and manufactured based on LoRa RF chip.
It integrates two interfaces of industrial standard RS485 and supports a variety of protocols to realise the data transmission between wired and wireless devices.
It supports LoRaWAN Class C protocol. It can be widely applied in the IoT, centralised metering and industrial control etc.
Reviews
There are no reviews yet.